| |
 Limited
Non-Transferrable Lifetime Warranty
Click here for bases for multiple holders
SALE
Current lead time to ship orders is 2-3 weeks.
Track Mount
This mount is designed for inside track dimensions of 3” wide and ¼”
thick (Cisco, Bert’s, Traxstech, and Tite-lok).
Plate slides into the track and locks in place with two thumbscrews.
MTTRW
$17.99
17.09
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Permanent
Thumbscrew Mount
This thumbscrew mount is for use with a single rod holder and comes with
two separate plates. The rod holder will mount to the top plate and the
bottom plate will mount directly to the gunnel. The two plates are
secured together by two thumbscrews and can be easily disassembled for
removal/storage from the gunnel.
The dimensions of the base are 3" x 4" and is machined from solid
aluminum and clear anodized finish. Thumbscrews secure into 1/4-20
threaded holes.
MTTSS
$23.99
22.79
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Rail Mount
The rail mount is designed for use with 7/8” or 1” diameter rails. The
clamp is positional at any place along the rail. You can get
the most versatility without drilling additional
holes in your boat!
MTRLS, MTRLS-1
$26.99
25.64
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Thumbscrew
Rail Mount
 | Single rod holder is attached to the top plate using two
thumbscrews. |
| Removing the rod holder leaves only the slim fitted mount
attached to the rail. |
| This mount is most practical when frequently removing rod
holders from the boat for storage or when a slim fitting boat cover
is used. (Especially on Ranger boats.) |
| Available for 7/8" (Most boats) or 1" rails (Nitro
boats). |
| Double, triple, or quad crossplates can be attached for multiple
rod holders. (Crossplate
purchased separately.) |
If you prefer to have multiple placements around your boat, just
purchase additional base mounts. This option allows you to move
your rod holders from base to base rather than purchasing additional rod
holders.
MTRTS, MTRTS1, MTRTS125
7/8" & 1" Rail $42.99
40.84
1.25" Rail $68.99
65.54
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Permanent
Mount
The single rod holder will mount on top of the two interior screws
leaving the two exterior holes open for mounting directly to the gunnel
of the boat.
The dimensions of the base are 3" x 4" and is machined from solid
aluminum and clear anodized finish.
MTPRS
$14.49
13.77
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Riser
Elevates or staggers rod holders. Made from 100% aircraft
grade aluminum and machined from solid material to offer a virtually indestructible riser.
Any Cisco Tube or Cradle Style Rod
Holders can be mounted to the top of this riser, as well as the
Sure-Lok Electronics
Mount. The riser can be mounted to any
Cross-Plate or
Mount for Single Rod Holders
Available in 5", 10" and 15" heights.
RIS XX
5" $32.99
31.34
10" $34.99
33.24
15" $36.99
35.14
20" $39.99
37.99
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
Gimbal Mount
Adjusts to angle up to 33° and rotates to any position to suit your
needs. When you have the unit in position simply tighten down the two
5/16" hex screws on the front side. To ensure that our gimbal mount will
NEVER slip we
also include a set screw on the back side of the mount (as shown in the
pictures to the right). After the two hex screws are tightened drive the
set screw into the top knurled ball of the mount and you are ready to
fish!
The pole and gimbal mount are machined from solid aluminum and are
machine matched from billet aluminum from first to last process. It is
designed for use with double, triple and quad plates, as well as for
downriggers. The view and/or print installation instructions please
click here.
MTGIM
$79.99
75.99
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Extra Gunnel Plate for Thumbscrew Bases &
Electronics Mounts
Use the thumbscrews in the base of the Permanent Thumbscrew Base or
Sure-Lok Mount to secure rod holders or electronics mounts down to the
threaded holes on the exterior ends of the mounting plate.
The dimensions of the base are 3" x 4" and is machined from solid
aluminum and clear anodized finish.
Available in Silver & Black
XPSLP, XPSLP-BK
Silver $13.99
13.29
Black $14.99
14.24
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Lund Trac Mounts
90° Pro Trac Heavy Duty
There are two main styles of track mounted to the gunnel of these
boats, 42° Sport Trac and 90° Pro Trac. Each has a
unique locking mechanism which allows the unit to slide along the track
and easily secure it in position by tightening the two knobs located at
the front of the unit. These knobs are held in place with spring
washers so that the vibrations of the boat do not allow anything to
vibrate loose. Two synthetic levelers at the end
of the unit to give the mount added support are also provided.
No tools required.
Quick & easy removal
Top mounting surface is 3" x 4"
A crossplate or
track can be mounted to the mount for
multiple rod configurations.
90 Degree also available in Heavy Duty for heavy or tall equipment.
For mounting heavy or tall equipment on the 42° Sport
Trac, mount a track to multiple mounts. (2 for 12"-18" tracks, 3 for
24"-48" tracks, 4 for 60"-72" tracks.)
Sample Set-Up
MTU42, MTU90, MTU90-DR
42º Sport Trac
$66.99
63.64
90º Pro Trac $66.99
63.64
90º Heavy Duty $125.99
119.69
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Tracker VersaTrack
Mount
Mounts to 90° Tracker VersaTrack. Has a
unique locking mechanism which allows the unit to slide along the track
and easily secure it in position by tightening the two knobs located at
the front of the unit. These knobs are held on place with spring
washers so that the vibrations of the boat do not allow anything to
vibrate loose. We also provide two synthetic levelers at the end
of the unit to give the mount added support.
No tools required.
Quick & easy removal
Top mounting surface is 3" x 4"
A crossplate or
track can be mounted to the mount for
multiple rod configurations.
For mounting heavy or tall equipment, mount a
track to multiple mounts. (2 for 12"-18" tracks, 3 for
24"-48" tracks, 4 for 60"-72" tracks.)
MTTRK
$66.99
63.64
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
|
No tools required
|
|
Quick & Easy removal
|
|
Has a
unique locking mechanism which allows the unit to slide along the track
and easily secure it in position by tightening the two knobs located at
the front of the unit.
|
|
The knobs are held on place with spring
washers so that the vibrations of the boat do not allow anything to
vibrate loose.
|
|
Two synthetic levelers at the end
of the unit provided to give the mount added support.
|
|
A single rod holder can be mounted to this unit
|
|
A crossplate or
track can be mounted to the mount for
multiple rod configurations.
|
|
For mounting heavy or tall equipment, mount a
track to multiple mounts. (2 for 12"-18" tracks, 3 for
24"-48" tracks, 4 for 60"-72" tracks.)
|
|
Top mounting surface is 3" x 4"
|
MTLWE
$66.99
63.64
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
Ranger VS Series 45º
Integrated Angled Track Mount
|
No tools required
|
|
Quick & Easy removal
|
|
Machined from a solid piece of aluminum bar and is
pressed to create the 45º
angled bend.
|
|
The slotted keys are made from stainless steel and
are attached to all solid aluminum components which complete the
round knobs.
|
|
You will know when your unit is locked into place
when the red line gauge is in the vertical position.
|
|
Also provided are two synthetic levelers at the
end of the unit to give the mount added support and to protect the
gunnel from unnecessary scratches.
|
|
A single rod holder can be mounted to this unit
|
|
A crossplate or
track can be mounted to the mount for
multiple rod configurations.
|
|
For mounting heavy or tall equipment, mount a
track to multiple mounts. (2 for 12"-18" tracks, 3 for
24"-48" tracks, 4 for 60"-72" tracks.)
|
|
Cisco, Scotty, Folbe, and Cabela's rectangular
hole patterns are pre-drilled and threaded into the mount.
|
|
Cannon, Big Jon, and Walker downrigger plates are
also available.
|
|
Top mounting surface is 3" x 4"
|
MTRTR
$66.99
63.64
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
|
No tools required
|
|
Quick & Easy removal
|
|
FitS securely in the Alumatrack system built into
the gunnel.
|
|
Can be used in Voyageur, Escape, Competitor,
Classic & Trophy Models.
|
|
Pre-drilled w/ 1/4-20 holes to attach a rod
holder, double/ triple/quad crossplates or downrigger adapter
plates.
|
|
A single Cisco, Scotty, Cabela or Folbe rod holder
matches the hole patterns.
|
|
A crossplate or
track can be mounted to the mount for
multiple rod configurations.
|
|
For mounting heavy or tall equipment, mount a
track to multiple mounts. (2 for 12"-18" tracks, 3 for
24"-48" tracks, 4 for 60"-72" tracks.)
|
|
Cannon, Big Jon, and Walker downrigger plates are
also available.
|
|
Top mounting surface is 3" x 4"
|
MTALM
$66.99
63.64
Dropshipped directly from Cisco
Switch to UPS Shipping Services during checkout
|
|
| |
